Sunday, September 13, 2009

CAR

An automobile or motor car is a wheeled motor vehicle used for transporting passengers, which also carries its own engine or motor. Most definitions of the term specify that automobiles are designed to run primarily on roads, to have seating for one to eight people, to typically have four wheels, and to be constructed principally for the transport of people rather than goods.However, the term automobile is far from precise, because there are many types of vehicles that do similar tasks.

As of 2002, there were 590 million passenger cars worldwide (roughly one car per eleven people).Around the world, there were about 806 million cars and light trucks on the road in 2007; they burn over 260 billion gallons of gasoline and diesel fuel yearly. The numbers are increasing rapidly, especially in China and India.

Production

Ransom E. Olds.

The large-scale, production-line manufacturing of affordable automobiles was debuted by Ransom Olds at his Oldsmobile factory in 1902. This concept was greatly expanded by Henry Ford, beginning in 1914.

As a result, Ford's cars came off the line in fifteen minute intervals, much faster than previous methods, increasing productivity eight fold (requiring 12.5 man-hours before, 1 hour 33 minutes after), while using less manpower. It was so successful, paint became a bottleneck. Only Japan black would dry fast enough, forcing the company to drop the variety of colors available before 1914, until fast-drying Duco lacquer was developed in 1926. This is the source of Ford's apocryphal remark, "any color as long as it's black". In 1914, an assembly line worker could buy a Model T with four months' pay.

Portrait of Henry Ford (ca. 1919)

Ford's complex safety procedures—especially assigning each worker to a specific location instead of allowing them to roam about—dramatically reduced the rate of injury. The combination of high wages and high efficiency is called "Fordism," and was copied by most major industries. The efficiency gains from the assembly line also coincided with the economic rise of the United States. The assembly line forced workers to work at a certain pace with very repetitive motions which led to more output per worker while other countries were using less productive methods.

In the automotive industry, its success was dominating, and quickly spread worldwide seeing the founding of Ford France and Ford Britain in 1911, Ford Denmark 1923, Ford Germany 1925; in 1921, Citroen was the first native European manufacturer to adopt the production method. Soon, companies had to have assembly lines, or risk going broke; by 1930, 250 companies which did not, had disappeared.

Development of automotive technology was rapid, due in part to the hundreds of small manufacturers competing to gain the world's attention. Key developments included electric ignition and the electric self-starter (both by Charles Kettering, for the Cadillac Motor Company in 1910-1911), independent suspension, and four-wheel brakes.

Ford Model T, 1927, regarded as the first affordable American automobile

Since the 1920s, nearly all cars have been mass-produced to meet market needs, so marketing plans often have heavily influenced automobile design. It was Alfred P. Sloan who established the idea of different makes of cars produced by one company, so buyers could "move up" as their fortunes improved.

Reflecting the rapid pace of change, makes shared parts with one another so larger production volume resulted in lower costs for each price range. For example, in the 1930s, LaSalles, sold by Cadillac, used cheaper mechanical parts made by Oldsmobile; in the 1950s, Chevrolet shared hood, doors, roof, and windows with Pontiac; by the 1990s, corporate drivetrains and shared platforms (with interchangeable brakes, suspension, and other parts) were common. Even so, only major makers could afford high costs, and even companies with decades of production, such as Apperson, Cole, Dorris, Haynes, or Premier, could not manage: of some two hundred American car makers in existence in 1920, only 43 survived in 1930, and with the Great Depression, by 1940, only 17 of those were left.

In Europe much the same would happen. Morris set up its production line at Cowley in 1924, and soon outsold Ford, while beginning in 1923 to follow Ford's practise of vertical integration, buying Hotchkiss (engines), Wrigley (gearboxes), and Osberton (radiators), for instance, as well as competitors, such as Wolseley: in 1925, Morris had 41% of total British car production. Most British small-car assemblers, from Abbey to Xtra had gone under. Citroen did the same in France, coming to cars in 1919; between them and other cheap cars in reply such as Renault's 10CV and Peugeot's 5CV, they produced 550,000 cars in 1925, and Mors, Hurtu, and others could not compete.Germany's first mass-manufactured car, the Opel 4PS Laubfrosch (Tree Frog), came off the line at Russelsheim in 1924, soon making Opel the top car builder in Germany, with 37.5% of the market.

See also: Automotive industry

Fuel and propulsion technologies

A Radio Taxi in New Delhi. A court order requires all commercial vehicles including trucks, buses and taxis in India to run on Compressed Natural Gas

See also: Alternative fuel vehicle

Most automobiles in use today are propelled by gasoline (also known as petrol) or diesel internal combustion engines, which are known to cause air pollution and are also blamed for contributing to climate change and global warming.Increasing costs of oil-based fuels, tightening environmental laws and restrictions on greenhouse gas emissions are propelling work on alternative power systems for automobiles. Efforts to improve or replace existing technologies include the development of hybrid vehicles, and electric and hydrogen vehicles which do not release pollution into the air.

Petroleum fuels

Diesel

Diesel-engined cars have long been popular in Europe with the first models being introduced as early as 1922 by Peugeot and the first production car, Mercedes-Benz 260 D in 1936 by Mercedes-Benz. The main benefit of diesel engines is a 50% fuel burn efficiency compared with 27% in the best gasoline engines. A down-side of the Diesel engine is that better filters are required to reduce the presence in the exhaust gases of fine soot particulates called diesel particulate matter. Manufacturers are now starting to fit[when?] diesel particulate filters to remove the soot. Many diesel-powered cars can run with little or no modifications on 100% biodiesel and combinations of other organic oils.

Gasoline

2007 Mark II (BMW) Mini Cooper

Gasoline engines have the advantage over diesel in being lighter and able to work at higher rotational speeds and they are the usual choice for fitting in high-performance sports cars. Continuous development of gasoline engines for over a hundred years has produced improvements in efficiency and reduced pollution. The carburetor was used on nearly all road car engines until the 1980s but it was long realised better control of the fuel/air mixture could be achieved with fuel injection. Indirect fuel injection was first used in aircraft engines from 1909, in racing car engines from the 1930s, and road cars from the late 1950s.Gasoline Direct Injection (GDI) is now starting to appear in production vehicles such as the 2007 (Mark II) BMW Mini. Exhaust gases are also cleaned up by fitting a catalytic converter into the exhaust system. Clean air legislation in many of the car industries most important markets has made both catalysts and fuel injection virtually universal fittings. Most modern gasoline engines also are capable of running with up to 15% ethanol mixed into the gasoline - older vehicles may have seals and hoses that can be harmed by ethanol. With a small amount of redesign, gasoline-powered vehicles can run on ethanol concentrations as high as 85%. 100% ethanol is used in some parts of the world (such as Brazil), but vehicles must be started on pure gasoline and switched over to ethanol once the engine is running. Most gasoline engined cars can also run on LPG with the addition of an LPG tank for fuel storage and carburettor modifications to add an LPG mixer. LPG produces fewer toxic emissions and is a popular fuel for fork-lift trucks that have to operate inside buildings.

The hydrogen powered FCHV (Fuel Cell Hybrid Vehicle) was developed by Toyota in 2005

Biofuels

Ethanol, other alcohol fuels (biobutanol) and biogasoline have widespread use an automotive fuel. Most alcohols have less energy per liter than gasoline and are usually blended with gasoline. Alcohols are used for a variety of reasons - to increase octane, to improve emissions, and as an alternative to petroleum based fuel, since they can be made from agricultural crops. Brazil's ethanol program provides about 20% of the nation's automotive fuel needs, as a result of the mandatory use of E25 blend of gasoline throughout the country, 3 million cars that operate on pure ethanol, and 6 million dual or flexible-fuel vehicles sold since 2003.that run on any mix of ethanol and gasoline. The commercial success of "flex" vehicles, as they are popularly known, have allowed sugarcane based ethanol fuel to achieve a 50% market share of the gasoline market by April 2008.

Electric

Main articles: Battery electric vehicle, Hybrid vehicle, and Plug-in hybrid

The Henney Kilowatt, the first modern (transistor-controlled) electric car.

2007 Tesla electric powered Roadster

Tata/MDI OneCAT Air Car

A CNG powered high-floor Neoplan AN440A, run on Compressed Natural Gas

The first electric cars were built around 1832, well before internal combustion powered cars appeared. For a period of time electrics were considered superior due to the silent nature of electric motors compared to the very loud noise of the gasoline engine. This advantage was removed with Hiram Percy Maxim's invention of the muffler in 1897. Thereafter internal combustion powered cars had two critical advantages: 1) long range and 2) high specific energy (far lower weight of petrol fuel versus weight of batteries). The building of battery electric vehicles that could rival internal combustion models had to wait for the introduction of modern semiconductor controls and improved batteries. Because they can deliver a high torque at low revolutions electric cars do not require such a complex drive train and transmission as internal combustion powered cars. Some post-2000 electric car designs such as the Venturi Fétish are able to accelerate from 0-60 mph (96 km/h) in 4.0 seconds with a top speed around 130 mph (210 km/h). Others have a range of 250 miles (400 km) on the United States Environmental Protection Agency (EPA) highway cycle requiring 3-1/2 hours to completely charge. Equivalent fuel efficiency to internal combustion is not well defined but some press reports give it at around 135 miles per US gallon (1.74 L/100 km; 162 mpg-imp).

Steam

Steam power, usually using an oil- or gas-heated boiler, was also in use until the 1930s but had the major disadvantage of being unable to power the car until boiler pressure was available (although the newer models could achieve this in well under a minute). It has the advantage of being able to produce very low emissions as the combustion process can be carefully controlled. Its disadvantages include poor heat efficiency and extensive requirements for electric auxiliaries.

Air

A compressed air car is an alternative fuel car that uses a motor powered by compressed air. The car can be powered solely by air, or by air combined (as in a hybrid electric vehicle) with gasoline/diesel/ethanol or electric plant and regenerative braking. Instead of mixing fuel with air and burning it to drive pistons with hot expanding gases; compressed air cars use the expansion of compressed air to drive their pistons. Several prototypes are available already and scheduled for worldwide sale by the end of 2008, though this has not happened as of January 2009. Companies releasing this type of car include Tata Motors and Motor Development International (MDI).

Gas turbine

In the 1950s there was a brief interest in using gas turbine engines and several makers including Rover and Chrysler produced prototypes. In spite of the power units being very compact, high fuel consumption, severe delay in throttle response, and lack of engine braking meant no cars reached production.

Rotary (Wankel) engines

Rotary Wankel engines were introduced into road cars by NSU with the Ro 80 and later were seen in the Citroën GS Birotor and several Mazda models. In spite of their impressive smoothness, poor reliability and fuel economy led to them largely disappearing. Mazda, beginning with the R100 then RX-2, has continued research on these engines, overcoming most of the earlier problems with the RX-7 and RX-8.

Rocket and jet cars

A rocket car holds the record in drag racing. However, the fastest of those cars are used to set the Land Speed Record, and are propelled by propulsive jets emitted from rocket, turbojet, or more recently and most successfully turbofan engines. The ThrustSSC car using two Rolls-Royce Spey turbofans with reheat was able to exceed the speed of sound at ground level in 1997.

Safety

Result of a serious automobile accident.

There are three main statistics to which automobile safety can be compared:

Deaths per

billion journeys

Bus: 4.3 Rail: 20 Van: 20 Car: 40 Foot: 40 Water: 90 Air: 117 Bicycle: 170 Motorcycle: 1640 Deaths per

billion hours

Bus: 11.1 Rail: 30 Air: 30.8 Water: 50 Van: 60 Car: 130 Foot: 220 Bicycle: 550 Motorcycle: 4840 Deaths per

billion kilometres

Air: 0.05 Bus: 0.4 Rail: 0.6 Van: 1.2 Water: 2.6 Car: 3.1 Bicycle: 44.6 Foot: 54.2 Motorcycle: 108.9

While road traffic injuries represent the leading cause in worldwide injury-related deaths, their popularity undermines this statistic.

Mary Ward became one of the first documented automobile fatalities in 1869 in Parsonstown, Ireland and Henry Bliss one of the United States' first pedestrian automobile casualties in 1899 in New York. There are now standard tests for safety in new automobiles, like the EuroNCAP and the US NCAP tests, as well as insurance-backed IIHS tests.

Costs and benefits

The neutrality of this section is disputed. Please see the discussion on the talk page. Please do not remove this message until the dispute is resolved. (December 2007)

Further information: Automotive industry

The costs of automobile usage, which may include the cost of: acquiring the vehicle, repairs, maintenance, fuel, depreciation, parking fees, tire replacement, taxes and insurance, are weighed against the cost of the alternatives, and the value of the benefits - perceived and real - of vehicle usage. The benefits may include on-demand transportation, mobility, independence and convenience.

Similarly the costs to society of encompassing automobile use, which may include those of: maintaining roads, land use, pollution, public health, health care, and of disposing of the vehicle at the end of its life, can be balanced against the value of the benefits to society that automobile use generates. The societal benefits may include: economy benefits, such as job and wealth creation, of automobile production and maintenance, transportation provision, society wellbeing derived from leisure and travel opportunities, and revenue generation from the tax opportunities. The ability for humans to move flexibly from place to place has far reaching implications for the nature of societies.

Environmental impact

The examples and perspective in this section may not represent a worldwide view of the subject. Please improve this article or discuss the issue on the talk page.

Further information: Global warming

Transportation is a major contributor to air pollution in most industrialised nations. According to the American Surface Transportation Policy Project nearly half of all Americans are breathing unhealthy air. Their study showed air quality in dozens of metropolitan areas has got worse over the last decade. In the United States the average passenger car emits 11,450 lbs (5 tonnes) of carbon dioxide, along with smaller amounts of carbon monoxide, hydrocarbons, and nitrogen.

Animals and plants are often negatively impacted by automobiles via habitat destruction and pollution. Over the lifetime of the average automobile the "loss of habitat potential" may be over 50,000 square meters (538,195 square feet) based on Primary production correlations.

Fuel taxes may act as an incentive for the production of more efficient, hence less polluting, car designs (e.g. hybrid vehicles) and the development of alternative fuels. High fuel taxes may provide a strong incentive for consumers to purchase lighter, smaller, more fuel-efficient cars, or to not drive. On average, today's automobiles are about 75 percent recyclable, and using recycled steel helps reduce energy use and pollution. In the United States Congress, federally mandated fuel efficiency standards have been debated regularly, passenger car standards have not risen above the 27.5 miles per US gallon (8.55 L/100 km; 33.0 mpg-imp) standard set in 1985. Light truck standards have changed more frequently, and were set at 22.2 miles per US gallon (10.6 L/100 km; 26.7 mpg-imp) in 2007. Alternative fuel vehicles are another option that is less polluting than conventional petroleum powered vehicles.

Other negative effects

Residents of low-density, residential-only sprawling communities are also more likely to die in car collisions[original research?] which kill 1.2 million people worldwide each year, and injure about forty times this number. Sprawl is more broadly a factor in inactivity and obesity, which in turn can lead to increased risk of a variety of diseases.

Future car technologies

Automobile propulsion technology under development include gasoline/electric and plug-in hybrids, battery electric vehicles, hydrogen cars, biofuels, and various alternative fuels.

Research into future alternative forms of power include the development of fuel cells, Homogeneous Charge Compression Ignition (HCCI), stirling engines, and even using the stored energy of compressed air or liquid nitrogen.

New materials which may replace steel car bodies include duraluminum, fiberglass, carbon fiber, and carbon nanotubes.

Telematics technology is allowing more and more people to share cars, on a pay-as-you-go basis, through such schemes as City Car Club in the UK, Mobility in mainland Europe, and Zipcar in the US.

Alternatives to the automobile

Established alternatives for some aspects of automobile use include public transit (buses, trolleybuses, trains, subways, monorails, tramways), cycling, walking, rollerblading, skateboarding, horseback riding and using a velomobile. Car-share arrangements and carpooling are also increasingly popular–the U.S. market leader in car-sharing has experienced double-digit growth in revenue and membership growth between 2006 and 2007, offering a service that enables urban residents to "share" a vehicle rather than own a car in already congested neighborhoods. Bike-share systems have been tried in some European cities, including Copenhagen and Amsterdam. Similar programs have been experimented with in a number of U.S. Cities. Additional individual modes of transport, such as personal rapid transit could serve as an alternative to automobiles if they prove to be socially accepted.